How to put real amp sounds (NAM captures) into the MK-300 and build one preset per song, from Stairway to Cliffs of Dover. Written so a 10-year-old can follow it.
USER PRESET01AMP 096 · PAGE DRAGON
Before you start: none of this has been tried on a real MK-300 yet. The gear for each song is what's commonly reported, and every setting is a starting point you finish by ear. Effect names marked "if present" aren't confirmed, so pick the closest one on your pedal.
Part 1
What the words mean
AmpThe box that makes the guitar loud and gives it a voice: clean, crunchy or screamy.
NAM captureA sound photograph of a real amp. Someone played a famous amp, and a computer learned to copy it. Your pedal plays that photo.
Cab / IRA photo of the speaker box. "Amp + Cab" captures already have it inside, so use those; they're easier.
PresetA saved outfit for one song: which amp, which effects, how loud.
SnapshotThe same outfit with a different jacket: one for rhythm, one for the solo (louder, with echo).
BlocksHelpers lined up like train cars. Each car does one job.
WAH→FX→GATE→DS→AMP (NAM)→CAB→EQ→MOD→DLY→REV→VOL
Golden rule: the amp comes from NAM. Pedals (overdrive, fuzz, wah, phaser, echo, reverb) come from the MK-300's own built-in blocks. NAM lives in the AMP block, and there's only one, so you can't stack a NAM pedal in front of a NAM amp.
Part 2 · Do this once
One-time setup
Charge the MK-300 until the battery is full.
Photograph every GLOBAL (GLOB) settings page. The firmware update below erases them.
On the laptop, go to m-vave.com/appdownload and download:
M-EFCS, the editor (the Windows ZIP). Unzip it and run it.
MK300 firmware V75. Rename it MK300_V75.fwsc and keep it.
Update the pedal from M-EFCS. Plug the USB cable in through a USB power blocker so the pedal doesn't pull power from the laptop. Don't unplug it until it says it's finished.
Make a free account at tone3000.com. You use it inside M-EFCS to download captures.
Plug in: guitar → MK-300 INPUT, then MK-300 OUTPUT → 1/4"-to-3.5 mm cable → Spark 2 AUX IN.
Spark 2: Music knob at the middle. Don't play anything over Bluetooth while you're playing guitar, because it adds delay.
MK-300 GLOBAL settings:
Output mode RCH = Nor (not NoCAB).
Input Gain: strum as HARD as you can. Turn it down until the input meter never touches the top. Check it again whenever you switch guitars, because humbuckers are louder.
Tail Control = Auto, so echoes don't chop off when you change presets.
Calibrate the expression pedal: rock it fully back, then fully forward, when the menu asks.
Part 3 · Load the amp photos
25 NAM captures into slots 96–120
Each song uses the most-downloaded matching capture on TONE3000. A capture made for the song or the guitarist comes first; if there isn't a popular one, it's the most-downloaded capture of the right amp. Download counts were checked on 20 Nov 2026, and every pick has an A2 version, which the MK-300 needs. Some songs share a capture, so 30 songs need 25 slots.
Slots: saving a capture replaces the amp that was in that slot. Slots 101–120 are bass amps. 96–100 are the last five guitar amps, so check you don't need those five first, or pick other slots and write them down.
Open the capture link (here or in the song's card) and press Download Tone (free TONE3000 account). Or find the same title in M-EFCS's TONE3000 section.
If the pack has several models, use the one in the Model column.
In M-EFCS: Import → AMP → Load NAM file, then Audition and choose A2 Lite.
Save to Device with the name and slot from the table.
For song 26 (Time), also download the Hiwatt Fane IR and save it with Import → CAB into CAB slot 100.
Slot
Save as
Capture on TONE3000
Model
Songs
Amp-head captures need a cab
Slot 110 (Mark I) and slot 117 (Hiwatt) are amp heads only. Turn the CAB block on: use a built-in cab, or the Hiwatt Fane IR for slot 117. IR files must be 24-bit mono WAV; a 32-bit float file fails with a "device is busy" error.
Good to know
Download counts change daily; these were the leaders on 20 Nov 2026.
TONE3000's licence lets you use the files freely but not re-share them.
"Amp + Cab" captures already contain the speaker, so leave the CAB block off.
Part 4 · Same steps for every song
Build a song preset
Pick an empty user preset. Keep songs in order: song 1, song 2, and so on.
AMP block = the song's NAM slot. CAB off for "Amp + Cab" captures, or CAB on with the matching IR for "Amp only" ones.
GATE on only where the song card says so. Raise the threshold just until the hiss between notes goes away.
Set every block as listed in the song's card below.
EQ block: Low Cut about 80 Hz, High Cut about 7 kHz. The Spark's small speakers like this.
Rhythm snapshot: delay off, your normal volume. Solo snapshot: +3 dB and delay on.
Set footswitch CtrlA to the solo snapshot.
Name the preset after the song and save. When all the songs are done, play each one at your normal volume and make them equally loud.
Part 5 · The song rack
The 30 songs: capture and settings
Tap a song to open its card: the NAM capture to download, the model to use, and a setting for every block. Delay times are starting points; if the delay has Tap, tap along to the song. Pickups: B = bridge (sharp), N = neck (warm), M = middle. Tick a song when you can play it; the ticks stay in this browser only.
Part 7 · Every block explained
What every block and knob does
This part follows the signal from the input to the output and explains every block and every knob, with pictures of what happens to the sound. Most pictures have sliders: drag them and watch the wave or curve change. Press Reset to go back to the starting setting. The knob names for AMP, DS and CAB come from the MK-300's own model list. For the other blocks this page uses the usual names for those effects, so your screen may word a few of them differently.
START
How to read the pictures
There are two kinds of picture on this page.
Wave pictures (time goes left to right) show what the speaker does: it pushes out and pulls in. A taller wave is louder, and a squashed, flat-topped wave is distorted.
Pitch pictures (low notes on the left, high notes on the right) show which parts of the sound get louder (line above 0) or quieter (line below 0). This is what tone knobs, EQ and speaker cabinets do.
Decibels (dB) measure loudness. Every −6 dB halves the wave's height. A 3 dB change is a small step you can just hear; about 10 dB sounds roughly twice as loud.Hertz (Hz) means how many times per second the wave wiggles, so low Hz is a low pitch. Your guitar's low E string is about 82 Hz. Each area of the picture has its own job in your tone.
Below 80 Hz: rumbleA guitar has almost nothing useful down here. Cut it, or small speakers like the Spark's flap and boom.
80–250 Hz: bodyThump and weight. Too much sounds boomy, too little sounds thin.
250 Hz–2 kHz: midsWhere a guitar lives. Mids make a solo cut through; too much sounds honky, like a horn.
2–6 kHz: bitePick attack and clarity. Too much hurts your ears.
Above 6 kHz: fizzOn distorted sounds this is the buzzy, bee-like part. Real guitar speakers barely play it.
GLOB
Input Gain
This is the first knob your guitar meets. It sets how strong the signal is before any block touches it, a bit like the volume on a microphone.
If it's set too high, the tops of the wave get cut off flat before the amp even sees them. That harsh sound can't be fixed later in the chain.
Input GainGLOB menu, firmware V73+
How strong your guitar signal is.
Up: amps and drives break up more, and you get more sustain and more noise.Down: cleaner and quieter, with less hiss, but tones can feel weak.
Start here: strum as hard as you ever will and set it so the meter peaks just under the top. NAM captures were recorded expecting a certain signal level, so if a capture sounds much too clean or too fuzzy, nudge this first. Check it again after switching between your humbucker and single-coil guitars.
WAH
Wah
A wah is a narrow boost that you slide from low to high pitch with your foot. It sounds like a voice saying "wow" or "wah". Hendrix used it on Watchtower, Slash on Sweet Child, and Kirk Hammett all over Metallica.
One hump moves as you rock the pedal: heel back gives a dark "ooh", toe forward gives a bright "eee".
Pedal positionexpression pedal
Where the hump sits.
Toe down: the hump moves high, bright and cutting.Heel down: the hump moves low, dark and throaty.
TypeX-Wah, Funk, Slide, Cry, Wah-Wah, Sense-Wah
Different hump shapes and sweep ranges. "Cry" types copy the classic Cry Baby. "Funk" is quackier.
Q / Rangeusual name
How narrow the hump is.
Up / narrow: a vocal, quacky sound.Down / wide: subtler, more like a tone knob.
SensitivitySense-Wah (auto wah)
On an auto-wah your picking moves the hump, not your foot.
Up: even soft picking opens it.Down: only hard picking opens it.
Start here: to turn the wah on, push the expression pedal past the end of its travel so it clicks the toe switch. Rock the pedal in time with the music, for example heel on the beat and toe between beats. Calibrate the pedal in GLOB so it uses its full range.
FX
FX: boost, compressor, pitch
A toolbox block that holds one of several "pre-amp" helpers: Boost, Compressor, Octave, Pitch, Whammy, Ring, Lofi or the auto-wahs. You only pick one at a time.
Boost (including the treble booster)
A boost makes the signal bigger before the amp, so the amp clips harder and sustains longer. It's an old trick: Brian May and Tony Iommi used treble boosters into cranked amps.
Level / Gain
How much bigger the signal gets.
Up: louder, or more drive if an amp comes after it.Down: it does almost nothing.
Type
A "clean boost" lifts every pitch. A treble booster mostly lifts the highs, giving a cutting, singing lead sound.
Compressor
Below the threshold nothing changes. Above it, loud playing is turned down; the steeper the ratio, the more it's squashed.The result: the loud pick is tamed and the fade is held up, so notes sustain and sound even. Knopfler's clean tone uses a light touch of this.
Threshold / Sustain
How loud a note must be before squeezing starts.
More sustain / lower threshold: more squeezing, longer notes, more noise.Less: natural playing with only the peaks caught.
Ratio
How hard it squeezes. 2:1 is gentle, 4:1 is obvious, and ∞:1 is a "limiter" that never lets anything past the threshold.
Attack
How fast it grabs a new note.
Slow: the pick "click" gets through first, which is punchier.Fast: smoother and flatter, and can sound lifeless.
Release
How fast it lets go after the note gets quieter.
Long: smooth, but can "pump".Short: natural, but can flutter.
Level / Output
Makes up the volume lost to squeezing. Set it so on and off sound equally loud.
Octave, Pitch, Whammy
One octave down means half as many wiggles per second; one octave up means twice as many.
Pitch / Interval
How far the extra note is moved, counted in semitones (frets). −12 is an octave down, +12 an octave up, and +7 is a "fifth", which makes power-chord-style harmonies.
Mix / Dry–Wet
How much of your real note versus the new note you hear. Keep both for a thick sound, or go 100% wet for "pitch only".
Whammy
The expression pedal bends the pitch up and down live, the screaming dive-bomb effect.
Ring / Lofi
Special effects. Ring modulation makes metallic, robot-like tones; Lofi makes a crunchy, old-radio sound.
GATE
Noise gate
A gate is a door. Loud sounds (your playing) open it, and when you stop playing it shuts so the hiss of a high-gain amp disappears. It's essential for Metallica and Pantera tones, and usually unnecessary for clean ones.
When the note fades below the threshold, the gate waits for the hold time, fades out over the release time, then stays silent.
Thresholdthe main knob
How loud a sound must be to get through.
Up: more silence, but it can cut off soft notes and the ends of long notes.Down: notes ring naturally, but some hiss gets through.
Release
How fast the door closes.
Long: a natural fade.Short: tight, chopped stops for fast chugging riffs.
Hold
How long the door stays open after the sound drops below the threshold, before it starts closing.
Range / Depth
How far it turns down when closed. At maximum it mutes completely; lower settings just make the noise quieter, which sounds more natural.
Detectfirmware V75
Chooses which signal the gate listens to when deciding to open. Try both settings and keep the one where soft notes still get through.
TypeAI Gate, AI Ms Gate, Soft, Hard, Pro
"AI" gates adjust themselves to your noise level. Soft fades gently; Hard snaps shut.
Start here: with the guitar silent, raise the threshold until the hiss just disappears. Then play one soft note and let it ring. If it gets chopped off, back the threshold down a little.
DS
Drive pedals: overdrive, distortion, fuzz
"Drive" means making the wave too big on purpose so its tops get squashed. The squashed wave adds new, higher pitches, and that's the crunchy, singing sound of rock guitar. How the tops get squashed is what makes each pedal different.
Try it: pick a pedal type and turn up Gain, and watch the tops flatten. Level only changes the height (volume), not the shape.
Clean: a smooth, round wave.Overdrive: tops gently rounded (Tube Screamer 2TS8, Blues OD).Distortion: tops flattened hard (Boss DS-1, 3DS1).Fuzz: almost a square, thick and buzzy (Fuzz Face, Big Muff).
Gain
How much the wave is squashed.
Up: more crunch, sustain and noise; chords get muddier.Down: cleaner, clearer chords, and you hear more of your picking.
Level
The pedal's output volume. Its biggest use is the boost trick: gain low and level high, so the pedal mostly pushes the amp harder and tightens it up.
Bass / Middle / Treble
Tone controls, just like the amp's (see the AMP pictures below). Tube Screamer-style pedals naturally cut bass and push mids, which is why they tighten a high-gain amp.
Reso / Pres / Bright
Extra tone knobs on some models, explained under AMP. V75 changed the Reso default to 0.
OverdriveRounded tops, the sound of a tube amp just breaking up. Bluesy and touch-sensitive: SRV, Gary Moore.
DistortionFlattened tops, more crunch and sustain: Nirvana, Prince, Satriani.
FuzzNearly square: a fat, buzzy, vintage sound. Hendrix, Gilmour. Your guitar's volume knob cleans it up a lot.
BoostNo squashing, just bigger. Used to push an amp.
AMP
Amp (your NAM capture goes here)
The amp block gives your guitar its personality. A real tube amp has three parts: a preamp (makes the drive), a tone stack (Bass/Middle/Treble), and a power amp and speaker (adds thump and bite). The knobs below control those parts on M-VAVE's own amp models.
With a NAM capture: the gain and tone were fixed when the capture was recorded. It's not confirmed which of these knobs, if any, act on a NAM model in this pedal; expect at least the level to. To get more or less gain, load another capture from the same pack. Shape the tone with the CAB cuts and the EQ block instead.
Bass lifts the lows, Treble lifts the highs, and Middle works in between. Turning the mids down (a "scoop") sounds big alone but can disappear in a band.Reso adds a low thump around 100 Hz. Pres adds bite above about 3 kHz, after the drive.Bright lifts the highs most at low gain. At high gain the drive covers it up.
Gain
How hard the preamp is pushed. Same idea as the DS gain pictures: rounder tops give a clean or crunch sound, flatter tops give a lead sound.
Up: crunch, then lead, more sustain and more noise.Down: clean and sparkly.
Level
The amp block's output volume. Use it to match presets; it doesn't change the tone.
Bass
Around 80–250 Hz.
Up: fuller and heavier, but boomy on small speakers.Down: tighter and thinner.
Middle
Around 400 Hz–1.5 kHz.
Up: solos cut through and sound vocal (Slash, Santana).Down: a "scooped" metal sound that's big alone but lost in a band.
Treble
Around 2–5 kHz.
Up: brighter, with more pick attack.Down: darker and smoother, like a jazz tone.
Reso (Resonance)
Low thump from the speaker pushing back on the amp.
Up: a bigger chug on palm mutes.Down: tighter. Keep it low on the Spark's small speakers.
Pres (Presence)
Upper bite added after the drive.
Up: sparkle and edge, harsh if overdone.Down: smooth and dark.
Bright
A treble lift, strongest at low gain. Use it to make clean tones sparkle.
Start here (built-in amps): everything at 12 o'clock (50), then change one knob at a time. Good to know: on real Marshall-style amps the tone knobs affect each other, so turning Middle down also changes how Bass and Treble sound.
CAB
Cabinet / IR
A guitar speaker is a filter. It plays almost nothing very low and drops sharply above about 5 kHz, and that's what turns a buzzy distorted signal into a warm guitar sound. The CAB block is a "sound photo" of a speaker box and microphone (an IR, short for impulse response).
Without a cab, distortion sounds like an angry bee. A 4x12 cab removes the rumble and the fizz.Low Cut and High Cut trim the two ends. Everything in the shaded middle is kept.
Model / IR
Which speaker box. 1x12 means one 12-inch speaker: tighter and boxier. 4x12 means four: bigger and deeper. The speaker type changes the flavour: Greenback is warm and vintage, V30 is aggressive in the mids, Jensen is Fender-sparkly, Alnico Blue is chimey.
Level
The cab's volume. Use it to match one IR's loudness to another's.
Low Cut
Removes everything below the frequency you set.
Up (e.g. 120 Hz): tighter, less boom.Down (e.g. 60 Hz): fuller, boomier on the Spark.
High Cut
Removes everything above the frequency you set.
Higher (e.g. 9 kHz): more air and more fizz.Lower (e.g. 5 kHz): smoother and darker, maybe dull.
Rule: an "Amp + Cab" NAM capture already contains the speaker, so turn CAB off; with two cabs the sound is dull and boxy. An "Amp only" capture needs CAB on. The output mode must be RCH = Nor for the Spark's AUX input.
EQ
EQ (equalizer)
A precise tone-shaping tool. Each band turns one area of pitch up or down. It comes after the amp and cab, so it shapes the finished tone. It's the best way to make a NAM capture fit the Spark.
Each band has three settings: where it acts (frequency), how much it boosts or cuts (gain), and how wide it is (Q).
Band gain (dB)
Boost or cut that area. Small moves of 2–4 dB go a long way.
Frequency (Hz)
Which area the band works on. Use the zone table at the top of this part.
Q (width)
High Q: narrow, for surgery such as removing one ugly ringing pitch. Low Q: broad and musical.
Modulation effects move something back and forth on their own, driven by a slow invisible wave called the LFO. Rate is how fast it moves; Depth is how far. Put them after the amp.
Chorus: a copy of your sound with a tiny delay that wobbles, like two guitarists slightly out of tune. It sounds lush and wide (Teen Spirit verses, Purple Rain).Flanger: a very short delay mixed back in cuts a row of notches. Sweeping it gives the "jet plane" whoosh.Phaser: a few wide notches sweep up and down, a swirly "whoosh" (Van Halen's Eruption). A Vibe is a throbbier relative (Hendrix).Tremolo: the volume goes up and down rhythmically, the surf and old-Fender sound.
Rate / Speed
How fast the movement is.
Up: warbly or helicopter-like.Down: slow and dreamy.
Depth / Intensity
How far it moves.
Up: obvious and seasick at extremes.Down: subtle shimmer.
Mix / Level
How much effect versus dry sound (chorus). For chorus, about 30–50% sounds natural.
Feedback / Resonance
Flanger and phaser only. Feeds the effect back into itself.
Up: sharper, more metallic, more "jet".Down: smoother.
Wave / Shape
Tremolo only. A smooth wave gives a gentle pulse; a square wave gives a choppy on/off.
Start here: rate low (about 20–30%), depth medium, mix about 40%. Then raise one setting at a time.
DLY
Delay (echo)
Delay plays your sound again a moment later, like shouting into a canyon. It makes solos sound bigger and longer. Gilmour's sound is half delay.
Time sets the gap between repeats, Mix sets how loud the first repeat is, and Feedback sets how fast the repeats die away.Higher feedback means more repeats. Near maximum they never stop and build into a howl.
Time / Tap
The gap between repeats, in milliseconds (ms).
80–150 ms: "slapback", a quick doubled sound (rockabilly, Stairway).
300–500 ms: classic solo echo.
In time with the song: delay ms = 60,000 ÷ BPM. At 120 BPM that's 500 ms per beat. A "dotted eighth" (U2-style) is 0.75 × that.
Tap tempo (FS4 in GLOB > Global BPM on V75) does the maths for you.
Feedback / Repeats
How many echoes.
Up: a long trail of echoes.Down: one or two repeats.
Mix / Level
How loud the echoes are compared with your playing.
Up: spacious, but can get messy.Down: felt more than heard. About 15–25% is a good place for solos.
Tone / High Cut
Darker repeats sit behind your playing so they don't clash with it. Analog and tape types are darker by design.
Modulation
A slight wobble on the repeats, like an old tape machine. Warm and dreamy.
Type
Digital: clean, exact repeats. Analog: darker and softer. Tape: warm and wobbly (Echoplex: Van Halen, Eric Johnson). Ping-pong / stereo: repeats bounce left and right (sounds mono through one speaker).
REV
Reverb (room sound)
Reverb is the sound of a space: thousands of tiny echoes bouncing off walls, blended into a smooth tail. Without it a guitar sounds dry and boxed in; with too much it sounds far away and washy.
Room: a short, natural tail, like playing in your bedroom.Hall: a long tail, with a small gap (the pre-delay) before it starts so the note stays clear.
Type
Room: small and natural. Hall: big and epic (Gilmour, Santana). Plate: smooth and bright, a studio classic (Van Halen). Spring: drippy, splashy, built into old Fender amps (SRV, Chuck Berry).
Decay / Time
How long the tail lasts.
Up: huge and dreamy, but fast playing gets blurry.Down: tight and close.
Pre-delay
A short gap before the reverb starts. 20–60 ms keeps your pick attack clear while adding space.
Mix / Level
How much reverb you hear. 15–25% for most songs, 30% or more for big ballad solos.
Tone / High Cut, Low Cut
Darker reverb (lower high cut) sounds more natural and less washy. Cutting lows from the reverb stops it getting muddy.
Order tip: set the chain to DLY → REV so the echoes also get the room sound. The factory order is REV → DLY.
VOL
Volume, pan and expression
Preset Vol (0–100)
The loudness of the whole preset. Use it to make every song equally loud; the solo snapshot adds about +3 dB.
Pan
Left or right placement. The Spark's AUX is effectively one speaker box, so keep it centred.
Volume pedal
With the expression pedal set to volume, start at the heel, pick a note, then rock forward. The note "swells" in like a violin.
GLOB
Global settings that change your sound
Tail Control Off: echoes stop dead when you change presets.Tail Control Auto: echoes ring out naturally into the next preset.
Tail ControlOff / Auto / Force Sync (V75)
What happens to delay and reverb tails when you switch presets or snapshots. Use Auto. Force Sync's exact behaviour isn't documented, so try it and listen.
RCH (output mode)
Nor: normal, with the cab included. Use this for the Spark's AUX. NoCAB: removes all cabs, only for plugging into a real guitar amp's input. Dry: unprocessed guitar.
Global BPM / Tap
One tempo for all time-based effects. Tap FS4 on the Global BPM page (V75).
Global EQ
One EQ applied to every preset. Use it to fit the Spark's speakers once (e.g. Low Cut 80 Hz) instead of fixing each preset.
USB Audio
For recording. NO LB is normal recording. NOR mixes in what the computer plays, so a backing track ends up in the recording. DRY records the clean guitar for re-amping. RESAMPLE sends computer audio through the pedal's effects.
Learning order
Easiest to hardest
Good to know
What a NAM file can hold
A capture can include
Overdrive, distortion, fuzz, boost
EQ / tone shaping
A wah stuck in one position
A pedal plus an amp together, e.g. "Plexi + TS808"
A capture can't include
Delay, reverb
Chorus, phaser, flanger, vibe
A wah you rock while playing
A compressor that pumps
Those change over time, and NAM only learns what happens in a fraction of a second. Use the MK-300's MOD, DLY and REV blocks.
Where to get captures
TONE3000: free, browsable inside M-EFCS.
Or download a .nam in a browser, then in M-EFCS choose Import → AMP → Load NAM file.
Look for the A2 badge. The pedal plays the "A2 Lite" version.
Part 6
Practise like a pro
Listen to the solo 3 times and hum it.
Learn 4 bars at a time. Record the backing chords in the looper, then play over them.
Slow first: drum machine at 60% of the song's speed. Speed up only after 3 clean runs in a row.
Play along with the real song over Bluetooth audio into the MK-300. A Bluetooth delay is fine for backing music.
Tone check: switch back and forth between your preset and the record. Too fizzy? Lower the High Cut or the gain. Muddy? Raise the Low Cut. Quiet in the solo? Use the solo snapshot's +3 dB.